Quck answer
Proper maintenance of a whirlpool tub is essential to ensure its longevity and optimal performance. Here are some key steps to follow:
1. Regular cleaning: Clean the tub after each use to prevent the buildup of soap scum, oils, and bacteria. Use a non-abrasive cleaner recommended for whirlpool tubs and a soft cloth or sponge.
2. Flush the jets: To remove any debris or bacteria that may accumulate in the jets, fill the tub with warm water and add a cleaning solution specifically designed for whirlpool tubs. Run the jets for 10-15 minutes, then drain the tub.
3. Avoid harsh chemicals: Use only approved cleaning products to prevent damage to the tub’s surface and components. Avoid bleach, abrasive cleaners, and harsh chemicals that can erode the tub’s finish or cause the jets to malfunction.
4. Check and replace filters: Regularly inspect the filters and replace them as recommended by the manufacturer. Clean filters ensure proper water circulation and prevent clogs.
5. Monitor water quality: Test the water regularly to maintain the correct pH and chlorine levels. Improper water chemistry can lead to corrosion, discoloration, or damage to the tub’s components.
By following these maintenance tips, you can enjoy a clean, hygienic, and functional whirlpool tub for years to come.
A jetted whirlpool bathtub provides a peaceful escape from the stresses of the world, unless it releases black specks or chunks of debris while in use. To ensure a relaxing bath, it is important to clean the tub and jets regularly.
When to Clean Jetted Bathtubs
A jetted tub requires more maintenance compared to a regular bathtub. The humid environment can cause mold, mildew, and bacteria to accumulate in the tub’s parts, especially in the jets, due to body oils, soaps, and dead skin cells.
According to US Inspect, it is recommended to clean a jetted whirlpool tub after each use and perform a deep cleaning at least once a month. After each use, wipe down the tub and gently clean the jets with an old toothbrush. Once a month, set aside time to thoroughly clean the tub and jets to prevent the growth of mold and bacteria.
Gather Your Cleaning Tools
Cleaning a jetted whirlpool tub can be challenging due to its various components. To effectively clean all the parts, you will need a set of tools and cleaning products.
An old toothbrush or a narrow nylon brush can be used to clean the crevices and water jets. An all-purpose bucket is useful for rinsing the tub’s edges and sides, while soft microfiber cloths are ideal for drying the surface. Hot water is recommended for cleaning, and latex or rubber cleaning gloves can make the job easier.
Expensive cleaners are not necessary for cleaning a jetted whirlpool tub. Baking soda and vinegar, when used in the correct proportions, are usually sufficient for a thorough cleaning. Stronger cleaners like bleach can be used for jets that are heavily soiled with soap scum or other debris.
Cleaning a Whirlpool Tub
Start by wiping the tub with a clean microfiber cloth to remove any dust, hairs, or particles that may have accumulated. Fill the tub with hot water until the jets are submerged a few inches. Add 2 cups of vinegar to the water and let it sit for 15 minutes.
According to Bob Vila, it is recommended to turn off the air induction valves before turning on the jets. Check the owner’s manual to see if the manufacturer recommends keeping the air induction valves open. Closed valves will force the water through the internal plumbing, resulting in a deeper clean. Run the jets for 10 to 15 minutes, with the valves either open or closed. Once the water runs clear from the jets, turn off the jets and drain the tub.
Rinse the debris down the drain and follow up with your preferred tub cleaner or a sprinkle of baking soda and a spritz of vinegar. Scrub the tub and jets using the cleaner, paying attention to the nooks and crannies with an old toothbrush or narrow scrub brush. Remove the air intake cover, clean it thoroughly inside and out, and rinse before reattaching. Finally, fill the tub with water, rinse off any remaining cleaners, and dry the surface.
